Subdividing a Block in Melbourne’s North: Cost, Process and Whether Yours Qualifies
Subdividing land in Victoria runs through five stages: check your title and planning controls, apply to council for a planning permit, get the plan of subdivision certified, obtain a Statement of Compliance once works are done, then register the plan with Land Use Victoria to create new titles. The statutory council fee for a two-lot subdivision permit is $1,537.00 in 2026–27.
Start with whether it’s worth doing, not how
Most subdivision articles walk you through the process. That’s the wrong order, because the process costs tens of thousands of dollars and roughly half the people who start it shouldn’t have.
So before anything else, here’s a screening test you can run in ten minutes with public data.
Compare what a house is worth on your street against what two units are worth. If the gap doesn’t comfortably exceed your build cost plus fees plus tax, stop.
Using Domain’s medians for sales in the 12 months to October 2026:
| Suburb | Median 3-bed house | Median 3-bed unit | Two units | Gross gap | Ratio |
|---|---|---|---|---|---|
| Epping | $687,000 | $610,000 | $1,220,000 | $533,000 | 1.78× |
| Craigieburn | $654,000 | $550,000 | $1,100,000 | $446,000 | 1.68× |
| Thomastown | $765,000 | $632,500 | $1,265,000 | $500,000 | 1.65× |
| Lalor | $758,000 | $625,000 | $1,250,000 | $492,000 | 1.65× |
Read that carefully, because the ranking is not what people assume.
Thomastown and Lalor are where the big old blocks are, and they’re where most subdivision activity in this corridor happens. But Epping has the strongest ratio: 1.78 times the single-house value, on the lowest house entry price of the four.
Why: Epping’s unit median of $610,000 is high relative to its house median of $687,000. The gap between buying a house and buying a unit is only $77,000 there. In Thomastown it’s $132,500. A narrow house-to-unit gap is exactly what makes subdivision stack up, because the units you create are worth nearly as much as the house you knocked down.
What that table does not tell you
I need to be blunt about its limits, because a gross gap is not a profit.
It excludes build costs, demolition, the permit, surveying, service authority connections, council contributions, legal and conveyancing fees, holding costs and finance interest while nothing is earning, selling costs, GST, and capital gains tax. Any of those can be large. Together they routinely consume the entire gap.
It also assumes two three-bedroom units physically fit on your block and are permitted. That depends on your lot’s area, dimensions, orientation, fall, easements and the planning controls over it. Plenty of blocks that look big enough aren’t.
Treat the table as a filter for whether to spend money investigating, not as a feasibility study. If your suburb’s ratio is below about 1.6, the answer is probably no before you start.
Why the house-to-unit gap drives everything
Worth a moment on the mechanism, because it explains the ranking and lets you apply it to any suburb.
In Epping, a three-bedroom house is $687,000 and a three-bedroom unit is $610,000. The gap is $77,000.
In Thomastown, it’s $765,000 and $632,500. The gap is $132,500.
A narrow gap means the market barely discounts a unit against a house. So the two dwellings you create sell for nearly as much each as the single house you demolished, and the uplift is large. A wide gap means buyers pay a real premium for a house over a unit, your new dwellings are worth proportionally less, and the uplift shrinks.
The test to run on your own street: find the three-bedroom house median and the three-bedroom unit median, and look at the gap as a percentage of the house price. Epping’s $77,000 is about 11% of its house median. Thomastown’s $132,500 is about 17%. The lower that percentage, the better subdivision stacks up.
Does your block qualify? Six things to check first
1. Your title. Order a current title search and the title plan. You’re looking for easements: drainage, sewer, carriageway, and any covenant or Section 173 agreement restricting further subdivision. A sewer easement running diagonally through the middle of a block can make a second dwelling impossible. This is the cheapest check and the one that most often ends the project.
2. Your zone. Subdivision in Melbourne’s north generally happens in residential zones, and the zone sets what’s permitted. Thomastown, Lalor, Epping, Mernda and Donnybrook are in Whittlesea City Council; Craigieburn is in Hume City Council. Two councils, two planning schemes, two sets of local policy.
3. Overlays. Bushfire, flooding, significant landscape, heritage, development contributions. Each adds conditions, cost and time to a permit application. Your council’s planning property report for the address will list them.
4. Lot area and dimensions. Area alone doesn’t decide it. A 650m² block at 15m wide subdivides very differently to a 650m² block at 10m wide, because each resulting lot needs frontage, access, setbacks, private open space and car parking.
5. Services. Where are the water, sewer, power, gas and telecommunications connections, and can a second lot be serviced without extending a main? Service authority requirements are a common source of unbudgeted five-figure costs.
6. Trees. Significant or protected trees, on your block or on the neighbouring one, can dictate where you’re allowed to build. Councils in this corridor take tree protection seriously.
The five stages, in order
Stage 1 — Feasibility and pre-application
Title search, title plan, planning property report, a survey, and ideally a pre-application meeting with your council’s planning department. A planner telling you “this won’t get through” before you’ve spent $30,000 is the best value available in this whole process.
A licensed surveyor and a town planner are the two professionals to engage first. Not a builder.
Stage 2 — Planning permit application
You apply to council to subdivide. The statutory fee is set by the Planning and Environment (Fees) Regulations, and for subdividing land into two lots it is $1,537.00 in 2026–27, up from $1,496.10 in 2025–26. Fees are set in fee units and indexed each financial year.
That fee is the council’s charge for assessing the application. It is not the cost of the subdivision. Your surveyor, planner and any required consultant reports are separate and considerably larger.
Council assesses the application against its planning scheme, may advertise it to neighbours, and may receive objections. Objections can push the matter to VCAT, which adds months and legal cost. If your proposal is marginal, this is where it dies.
What you get at the end is a permit with conditions attached. Read the conditions. They’re where the real costs hide.
Stage 3 — Certification of the plan of subdivision
Your surveyor prepares a plan of subdivision and submits it to council for certification under the Subdivision Act 1988. Certification confirms the plan matches the permit and meets statutory requirements. Referral authorities get involved here: the water authority and the electricity distributor.
Stage 4 — Statement of Compliance
You complete the works and obligations the permit conditions require: service connections, drainage, any required contributions or works-in-kind. Once council and the referral authorities are satisfied, council issues a Statement of Compliance.
This is the stage that takes longest and blows budgets most often, because it’s where theoretical conditions become physical work.
Stage 5 — Registration
The certified plan and the Statement of Compliance go to Land Use Victoria for registration. Registration creates the new titles. Until that happens, the new lots legally do not exist and cannot be sold or separately mortgaged.
Subdivide, knock down and rebuild, or just sell?
Three options, and the right one depends less on the block than on you.
Subdivide and sell the vacant lots. Lowest risk, lowest return, fastest. You take the planning risk and the works cost, then exit without construction risk. Worth considering if the ratio table above is marginal.
Subdivide and build. Highest return, highest risk, longest. You’re now a developer with construction risk, finance costs, and a sales campaign at the end into a market you can’t predict.
Sell as is, to someone else who’ll do it. Often underrated. A development-ready block with a permit already approved sells to builders and developers who’ll pay for the de-risking you’ve done. If you don’t want construction risk, getting a permit and selling with it attached can capture a good share of the uplift for a fraction of the exposure.
Knock down and rebuild one house. A different project entirely, and the right answer if your block won’t support two dwellings but your house is past saving. It doesn’t create a new title, so none of the five stages above apply.
Three tax and cost traps
Vacant residential land tax. This catches subdividers specifically. The State Revenue Office notes the tax may apply to existing and uninhabitable homes, homes under construction or renovation, and undeveloped land. Metropolitan Melbourne land left undeveloped for five or more continuous years and capable of residential development is assessed at 1% of capital improved value. If you demolish and then stall, waiting on a permit, waiting on finance, waiting on the market, you can be paying this on a vacant site. Notification to the SRO is due by 15 February each year, and the obligation is yours.
Land tax during the project. Land that isn’t your principal place of residence attracts land tax on site value as at 31 December, at $1,350 plus 0.3% of the amount over $300,000 in the $300,000–$600,000 band. A principal place of residence exemption can cover land you’re building on, with conditions and time limits attached, confirm your own position with the SRO or your conveyancer.
GST and capital gains tax. Selling newly built residential property can bring you into the GST system if you’re treated as carrying on an enterprise, and capital gains tax may apply to land that isn’t your main residence. These are genuinely complicated and the answer depends on your circumstances, your history of similar projects, and how the property has been used. Get advice from an accountant before you start, not after you’ve sold. Getting this wrong is the most expensive mistake available in this whole process, and it’s the one people discover last.
What I’d tell you if you called
Run the ratio test on your own suburb first. If you’re in Epping with a 650m² block and a tired house, the numbers are more interesting than they are almost anywhere else in this corridor, and the title search is $50 well spent.
If you’re in Thomastown or Lalor, you’re in the right suburbs for stock but the ratios are tighter than people assume, so the title and planning checks matter more.
And if your block has an easement through the middle of it, the project is over. Find that out in week one rather than month six.
We’re agents, not planners or surveyors, and the professional advice above should come from people licensed to give it. What we can do is tell you what two units on your street actually sell for, what a development-ready block with a permit is worth to a builder, and whether selling as is beats the whole exercise. That conversation is free and it’s usually the one that saves the most money.
Frequently asked questions
1. How much does it cost to subdivide land in Victoria? The statutory council fee for a two-lot subdivision planning permit is $1,537.00 in 2026–27, up from $1,496.10 the previous year. That’s only the application fee, surveying, town planning, consultant reports, service connections, drainage works, council contributions and legal costs are all separate and considerably larger. Get itemised quotes rather than relying on a range, because costs vary enormously with your block’s conditions.
2. How do you subdivide land in Victoria? Five stages: check your title and planning controls, apply to council for a planning permit, have the plan of subdivision certified under the Subdivision Act 1988, complete the permit conditions and obtain a Statement of Compliance, then register the plan with Land Use Victoria to create the new titles. The new lots don’t legally exist until registration.
3. Does my block qualify for subdivision? Check six things: your title for easements and restrictive covenants or Section 173 agreements, your zone, any overlays on the planning property report, your lot’s area and frontage dimensions, whether a second lot can be serviced without extending a main, and any protected trees. An easement through the middle of the block is the most common dealbreaker.
4. How long does subdivision take? There’s no reliable single answer, because the timeline depends on your council’s workload, whether the application is advertised, whether neighbours object, and how much physical work the permit conditions require. The Statement of Compliance stage is typically the longest. If objections push the matter to VCAT, add months.
5. Do I need council approval to subdivide? Yes. You need a planning permit from the responsible authority, which is your local council, Whittlesea City Council for Thomastown, Lalor, Epping, Mernda and Donnybrook, or Hume City Council for Craigieburn. The plan of subdivision then needs certification, and the council issues the Statement of Compliance once conditions are met.
6. What is a dual occupancy? Two dwellings on one lot. It’s a different proposition to subdivision, you can build two dwellings without creating two titles, or you can subdivide to create separate titles, or you can do both. Which is possible depends on your zone and the planning controls over your land. Separate titles generally improve saleability and financing but require the full subdivision process.
7. Is it better to subdivide or sell as is? It depends on your appetite for risk and time. Selling as is with an approved planning permit attached is an underrated middle path, you capture a share of the uplift for having de-risked the project, without taking construction risk. If the value ratio between a house and two units on your street is below roughly 1.6, selling as is is often the better answer.
8. What is the minimum lot size for subdivision in Whittlesea or Hume? There’s no single number that applies everywhere, because requirements come from the zone, any schedules to it, and the specific planning controls over your land. Get your council’s planning property report for the address and speak to the planning department before you assume a figure. Area alone doesn’t decide it anyway, frontage, access and setbacks matter as much.
9. Do I pay GST on a subdivision? Possibly. Selling newly built residential property can bring you into the GST system if you’re treated as carrying on an enterprise, and capital gains tax may apply to land that isn’t your main residence. The answer depends on your circumstances and your history of similar projects. Get advice from an accountant before you commit, because this is the most expensive thing to get wrong.
10. Is knock-down-rebuild cheaper than subdividing? It’s a different project. A knock-down-rebuild replaces one house with one house and creates no new title, so none of the subdivision stages apply and the cost and timeline are much shorter. It’s the right answer when your block won’t support two dwellings but the house is past repair. It doesn’t deliver the value uplift that creating a second title can.
More from One Group Realty
Building and Pest Inspection Cost in Melbourne (2026): Prices, What’s Included and When You Need One
Read article →
Cooling-Off Period in Victoria: When It Applies, When It Doesn’t, and What It Costs
Read article →
Cheapest Suburbs in Melbourne’s North: Three-Bedroom House Prices Ranked (Late 2026)
Read article →Find out what your property is worth
A free, no-obligation appraisal from an agent who sells in your street.